产品品牌： 欧莱斯 详细说明： 1、本产品采用高级进口丙烯酸树脂和高级颜料经过细制研磨加工组合而成，适用范围：各种金属、玻璃、陶瓷、石材、电镀(含水电镀)、阳极氧化铝表面、静电喷漆面及烤漆面等制品的丝印及移印，不需加固化剂，不需烘烤，即可获得优异的附着力。 2、产品特性：平光、附着力佳、流平性佳、硬度强、耐酒精、耐冲压、抗刮伤、耐化学品。 3、稀释剂：建议采用本公司配套专用稀释剂开油。 4、固化剂：本产品无需加固化剂，切勿加不配套的固化剂，会影响其效果 5、油墨调配方法：搅拌时先加稀释剂10%左右稀释到印刷适合粘度。 6、干燥时间：表干时间自然挥发5-10分钟，实干时间在24小时以内，48小时后达最佳性能，烤箱80℃烘烤30分钟性能更优。 7、使用期限：半年，过期请弃用，加了其他助剂剩余油墨不可回收。【油墨使用注意事项】 1、试印确认符合要求后再批量生产。 2、做好被印物的表面清除油脂及杂质工作，以促进附着效果。 3、附着力、硬度、耐酸性、耐酒精性、耐化学品性、抗划伤性、耐磨性等性能的检测，需要完全固化后方可检测。 4、未经允许情况下，不得将本系列油墨与其它类型油墨混用及配色。 5、丝网印刷加适量拉丝膏用本公司特慢干稀释剂更适宜印刷工艺顺畅。 6、注意作业车间的湿度，湿度过大会影响附着力，温度高容易堵网。【油墨性能检测结果】 1、3M胶纸粘在画有百格的油墨表面45度角迅速拉起不脱油。 2、纯度99%的酒精500G力在油墨表面来回擦拭100次无脱色。【油墨使用安全规则】 1、油墨，稀释剂使用及储存时严禁烟火 2、使用时注意施工场所的通风状况良好。 3、尽量避免皮肤直接接触。 4、本品不慎溅入口、鼻、眼、耳内，应用大量水清洗或直接求助医生。 5、对本品过敏者，使用前应涂覆一层皮肤扶肤膏或戴不渗透手套。 6、注意作业车间的湿度，湿度过大会影响附着力，温度高容易堵网
The characteristics of ink:Have and Germany Caili treasure the same color, is mainly used for PP, PE, BOPP and other materials, with a high color, high color, high covering power, high alcohol and wear resistance, high stability.Printing: silk screen printing can be.Table dry and work time: surface dry time natural volatile 5-10 minutes; work time within 24 hours.Dilution and cleaning: SV3 slow dry open water, UVK1 ( printing open water ) can be simultaneously used 718 washing network water cleaning.Test method ( completely dry):1, 3M gummed paper with ink surface adhesion in the painting, the 45 degree angle quickly pulled off the oil;2, purity 99% of industrial alcohol, one kilogram of weight of cotton pack in the ink surface, the horizontal force and pull 200 times without decolorization;3, wear resistance: the eraser 500g force level wipe 500 times back and forth.Method of use:1, before the use should be fully mixing, use at any time after the closure;2, mixing an additional 10-15% in oil and water, diluted to printing viscosity;3, mesh plug mesh can be used when washing network water cleaning;4, shall not be mixed with other types of ink.Matters needing attention:1, the plastic material similar in appearance, but may be of different materials, customers need to try to determine its requirements, and then batch printing;2, in the printing process, such as drawing or spread out, may be appropriate to add some cream to slow drying;3, the ambient temperature is too high, it will affect the quality of the original ink;4, according to the climate change, please stay away from fire, stored in a dark
